In-house component · Injection moulding
The face of the unit,
moulded in-house.
Fascias, louvres, grilles and structural plastic parts — moulded under the same roof, so the fit to chassis and coil is engineered, not negotiated.
Why in-house
Your brand's front,
our chassis behind it.
The fascia is the part a buyer sees and the part a brand owns. It also has to seal against the chassis, clear the louvres, hold the display bezel and pass the intake grille's airflow — dimensions that belong to the coil and fan behind it.
Because the moulds are cut in Ezentech's own tool room and run on Ezentech presses, a brand-specific front can be developed against the real chassis and validated on the line, not on a drawing.
- Split fascia widths — 830, 930, 1100 mm
- 03
- Window cabinet width, one front
- 660 mm
- Tool and die room for moulds
- In-house
- Environmental management system
- ISO 14001
Parts we mould
05 parts
- Front panel and fascia
- The indoor unit's outer face, tooled to the brand's industrial design and clipped to the chassis with real seam control.
- Learn more
- Louvres and vanes
- Horizontal deflector louvres and vertical vanes that steer the airflow from the outlet.
- Intake grille
- The top-deck intake that sets the airflow into the two-row evaporator coil behind it.
- Air outlet and cavity
- The recessed lower outlet and interior ducting that carry the indoor fan's 850–1,100 m³/h.
- Display bezel and control window
- The display module surround, LED windows and IR receiver window on the fascia.
From the sheet
The chassis
every fascia fits.
Indoor platforms as printed — the widths a brand's fascia is tooled to, with the coil and airflow behind each.
Indoor platforms the fascias fit
05 platforms
| Row | Evaporator coil | Air flow | Fan motor | Models |
|---|---|---|---|---|
| 830-17" chassis830x235x315 mm | 620x25.4x378 mm | 850 m³/h | DC · 35W · 1280 rpm | |
| 930-20" chassis930x315x235 mm | 725x25.4x378 mm | 1,000 m³/h | DC · 35W · 1280 rpm | |
| 930-22" chassis930x315x235 mm | 725x25.4x378 mm | 1,000 m³/h | DC · 35W · 1280 rpm | |
| 1100-22" chassis1100x315x235 mm | 887x25.4x378 mm | 1,100 m³/h | DC · 57W · 1350 rpm | |
| Window cabinet660x690x428 mm | 887x25.4x378 mm | 900 / 1,100 m³/h | AC · 110W · 1300 rpm / AC · 160W · 1300 rpm |
830-17" chassis830x235x315 mm
- Evaporator coil
- 620x25.4x378 mm
- Air flow
- 850 m³/h
- Fan motor
- DC · 35W · 1280 rpm
- Models
930-20" chassis930x315x235 mm
- Evaporator coil
- 725x25.4x378 mm
- Air flow
- 1,000 m³/h
- Fan motor
- DC · 35W · 1280 rpm
930-22" chassis930x315x235 mm
- Evaporator coil
- 725x25.4x378 mm
- Air flow
- 1,000 m³/h
- Fan motor
- DC · 35W · 1280 rpm
- Models
1100-22" chassis1100x315x235 mm
- Evaporator coil
- 887x25.4x378 mm
- Air flow
- 1,100 m³/h
- Fan motor
- DC · 57W · 1350 rpm
On the line
From industrial design
to moulded part.
Process
05 steps
Part design and DFM
The brand's design is checked for draft, wall thickness, clip geometry and fit against the target chassis.Tool build
Moulds are cut and finished in the in-house tool and die room, alongside the press tools for sheet metal.Sampling
First-off parts are moulded and fitted to a real chassis and coil; adjustments go straight back to the tool room.Production moulding
Parts run on Ezentech presses in the material and finish the brand signed off.Fit check on the line
Fascias are fitted on the assembly line and the finished unit goes through the psychrometric test with the production front in place.
Buyer questions
Before you
write the RFQ.
Frequently asked
03 questions
Can a brand have its own fascia design?
Yes. A brand-specific fascia is tooled in the in-house tool room and moulded on Ezentech presses to fit the 830, 930 or 1100 mm chassis, or the window front, without changing the unit behind it.
Who owns the fascia tooling?
That depends on the engagement model. In an OEM programme the partner typically owns the tool; in ODM and private-label programmes Ezentech's tooling is used. The arrangement is fixed in the RFQ.
Which plastic parts are moulded in-house?
The front panel and fascia, louvres and vanes, intake grille, air outlet and cavity, and the display bezel and control windows.
Planning a programme that needs injection moulding? Send the requirement — capacity, volume, chassis — and we will come back with a production plan.
Start the conversation
Let’s build
your next range.
From spec to shipped — send us your requirement and get a structured, engineering-backed quote.
OEM / ODM · Private label · Contract manufacturing